收藏本站
Atmel AT25128B/256B
WRITE SEQUENCE (WRITE): In order to program the Atmel ? AT25128B/256B, two separate instructions must be
executed. First, the device must be write enabled via the Write Enable (WREN) Instruction. Then a Write instruc-
tion may be executed. Also, the address of the memory location(s) to be programmed must be outside the
protected address field location selected by the Block Write Protection Level. During an internal write cycle, all
commands will be ignored except the RDSR instruction.
A Write Instruction requires the following sequence. After the CS line is pulled low to select the device, the Write
op-code is transmitted via the SI line followed by the byte address and the data (D7 - D0) to be programmed (see
Table 3-6 for the address key). Programming will start after the CS pin is brought high. (The Low-to-High transition
of the CS pin must occur during the SCK low time immediately after clocking in the D0 (LSB) data bit.
The Ready/Busy status of the device can be determined by initiating a Read Status Register (RDSR) Instruction. If
Bit 0 = 1, the Write cycle is still in progress. If Bit 0 = 0, the Write cycle has ended. Only the Read Status Register
instruction is enabled during the Write programming cycle.
The AT25128B/256B is capable of a 64-byte Page Write operation. After each byte of data is received, the six low
order address bits are internally incremented by one; the high order bits of the address will remain constant. If
more than 64 bytes of data are transmitted, the address counter will roll over and the previously written data will be
overwritten. The AT25128B/256B is automatically returned to the write disable state at the completion of a Write
cycle.
Note:
If the device is not write enabled (WREN), the device will ignore the Write instruction and will return to the standby
state, when CS is brought high. A new CS falling edge is required to re-initiate the serial communication.
Table 3-6.
Address Key
Address
A N
Don’t Care Bits
Atmel AT25128B
A 13 ? A 0
A 15 ? A 14
Atmel AT25256B
A 14 ? A 0
A 15
9
8698C–SEEPR–8/11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT25256T2-10TI-2.7 IC EEPROM 256KBIT 3MHZ 20TSSOP
AT25320AY6-10YH-1.8 IC EEPROM 32KBIT 20MHZ 8DFN
AT25640T1-10TI-2.7 IC EEPROM 64KBIT 3MHZ 14TSSOP
AT25DF321-SU IC FLASH 32MBIT 70MHZ 8SOIC
AT25F1024AN-10SU-2.7 IC FLASH 1MBIT 33MHZ 8SOIC
AT25F2048N-10SU-2.7 IC FLASH 2MBIT 33MHZ 8SOIC
AT25F4096W-10SU-2.7 IC FLASH 4MBIT 33MHZ 8SOIC
AT25HP512W2-10SI-2.7 SL383 IC EEPROM 512KBIT 10MHZ 16SOIC
相关代理商/技术参数
AT25256B-SSHL-B-RET 制造商:Atmel Corporation 功能描述:
AT25256B-SSHL-T 功能描述:电可擦除可编程只读存储器 256Kbit; SPI Bus High Spd; Mode 0 & 3 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25256B-SSHL-T SL901 制造商:Atmel Corporation 功能描述:IC EEPROM 256KBIT 20MHZ 8SOIC
AT25256B-SSHL-T 制造商:Atmel Corporation 功能描述:Serial EEPROM IC
AT25256B-XHL-B 功能描述:电可擦除可编程只读存储器 256Kbit; SPI Bus High Spd; Mode 0 & 3 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25256B-XHL-T 功能描述:电可擦除可编程只读存储器 256Kbit; SPI Bus High Spd; Mode 0 & 3 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25256B-XHL-T SL901 制造商:Atmel Corporation 功能描述:IC EEPROM 256KBIT 20MHZ 8TSSOP
AT25256C1-10CC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:SPI Serial EEPROMs